详细信息
機器操作使用油壓操作系統，機器動作穩定。
採用PLC控制器與圖形顯示觸控熒幕，操作最穩定、簡便。
結幫參數（行程與時間）的設定，以數值方式輸入，並設有鑰匙開關保護，防止未授權人員的不當更改。
PLC控制器可儲存500組鞋型結幫參數資料和爪型位置記憶，並具有爪盤寬度快速調整功能共有5段。
具備自我偵錯功能，節省故障排除時間。
爪盤位置調整採用電動操控,配合雙點快速調整設計,使爪盤可以左右分別張開。
中爪可向左右做各15度的偏擺調整，偏擺角度同時顯示與觸控熒幕。
中爪與左右二爪的銜接角度變化最多為20度。
第五爪可設定自動旋轉動作，使內腰轉折處的結幫效果最佳。
爪子可以獨立設定自動下拉行程或手動操作的升降，讓鞋面的張力平衡，以修正結幫最佳位置
爪子夾持鞋面後，可手動操控個別爪子的放開與再夾持。
爪子夾持壓力可設定於內撐台二次上升時進行洩壓動作。
內撐台上升高度，由機台外部調整，高度數值同時顯示與觸控熒幕。
內撐台上升可設定為兩段動作，配合後跟頂座動作，可防止楦頭下滑。
膠盤可採用兩段式結構，除快速寬度調整外，另可做左右腳內外腰的自動變化，達成最佳膠著點。
膠盤的前後位置，可藉由機台前方的手輪調整，最大可達16MM。
壓頭機構採用可調二段式壓力，在一次壓的操作調整中，可依需要設定為定壓控制或定位控制。
最新設計的掃刀大座下降位置調整，操作簡單。
掃刀機構前進動作，採用兩段速度調整。
標準配備：輔助掃刀機構、輔助壓邊機構和鞋頭十字燈機構。
Fully oil pressure operation system , the machine is more stable when it is working.The PLC system with the graphic display touch screen make the machine operation stable and simple.
Set parameters(stroke and time) by entering numbers, and set key switch to prevent the changing bynon-authorized.
The PLC controller can memorize 500 groups of shoe lasting parameter data and location of pincers, and ithas the function of adjusting claw plate quickly.
Error diagnostic function and save trouble shooting time.
The position adjustment of the claw plate adopts electric control, with the double point quick adjustment design, so that the claw plate can be opened to the left and right.
The middle pincer can make 15 degrees deflection to the left and right ,The yaw angle is also displayed onthe touch screen
The max angle of connection between the middle pincer and the left and right two pincers is 20 degrees.
The fifth pincer can be set automatic rotation action to make the inner waistlast ofthe best effect.
The pincer can be set to automatic pul-down stroke independently or manually operated lifting, allowingthe tension ofthe vamp to be balanced to correct the optimal position of the lasting.
After the pincer holds the vamp, the release and damping of the pincers can be controlled manually.
The pressure can be set relief action at the second rise of the inner support table.
The height of the inner support table is adjusted by the outside and is displayed on the touch screen.
The inner support table rise can be set as a two-stage action with the heel top seat action to prevent the lastslide.
The glue tray can be used in two-stage structure, it can adjust the width rapidly, and also do the automatic change ofthe left and right feet inside and outside the waist to achieve the best sticking point.
The distance offront and rear positions of the inner support platform can be up to 16mm, it can be adjustedby the hand wheel .
The indenter mechanism adopts adjustable two-stage pressure, and it can be set to constant pressure con-trol or positioning control during the first pressure.
The latest design of the large seat of the sweep knife descending position adjustment.
The forward motion ofthe wiper mechanism adopts double speed adjustments.
Standard equipment: Auxiliary sweep knife mechanism, auxiliary blank holding mechanism and toe crossight structure.
English
